ChangeSet 1.1790.2.9, 2004/08/02 15:36:10-07:00, nacc@us.ibm.com
[PATCH] PCI Hotplug: ibmphp_hpc: replace long_delay() with msleep()
Replace long_delay() with msleep() to guarantee the task
delays as desired.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
drivers/pci/hotplug/ibmphp_hpc.c | 19 +++++++++----------
1 files changed, 9 insertions(+), 10 deletions(-)
diff -Nru a/drivers/pci/hotplug/ibmphp_hpc.c b/drivers/pci/hotplug/ibmphp_hpc.c
--- a/drivers/pci/hotplug/ibmphp_hpc.c 2004-08-23 11:08:05 -07:00
+++ b/drivers/pci/hotplug/ibmphp_hpc.c 2004-08-23 11:08:05 -07:00
@@ -205,7 +205,7 @@
// READ - step 4 : wait until start operation bit clears
i = CMD_COMPLETE_TOUT_SEC;
while (i) {
- long_delay (1 * HZ / 100);
+ msleep(10);
wpg_addr = WPGBbar + WPG_I2CMCNTL_OFFSET;
wpg_data = readl (wpg_addr);
data = swab32 (wpg_data);
@@ -221,7 +221,7 @@
// READ - step 5 : read I2C status register
i = CMD_COMPLETE_TOUT_SEC;
while (i) {
- long_delay (1 * HZ / 100);
+ msleep(10);
wpg_addr = WPGBbar + WPG_I2CSTAT_OFFSET;
wpg_data = readl (wpg_addr);
data = swab32 (wpg_data);
@@ -316,7 +316,7 @@
// WRITE - step 4 : wait until start operation bit clears
i = CMD_COMPLETE_TOUT_SEC;
while (i) {
- long_delay (1 * HZ / 100);
+ msleep(10);
wpg_addr = WPGBbar + WPG_I2CMCNTL_OFFSET;
wpg_data = readl (wpg_addr);
data = swab32 (wpg_data);
@@ -333,7 +333,7 @@
// WRITE - step 5 : read I2C status register
i = CMD_COMPLETE_TOUT_SEC;
while (i) {
- long_delay (1 * HZ / 100);
+ msleep(10);
wpg_addr = WPGBbar + WPG_I2CSTAT_OFFSET;
wpg_data = readl (wpg_addr);
data = swab32 (wpg_data);
@@ -748,7 +748,7 @@
done = TRUE;
}
if (!done) {
- long_delay (1 * HZ);
+ msleep(1000);
if (timeout < 1) {
done = TRUE;
err ("%s - Error command complete timeout\n", __FUNCTION__);
@@ -891,7 +891,7 @@
case POLL_SLEEP:
/* don't sleep with a lock on the hardware */
up (&semOperations);
- long_delay (POLL_INTERVAL_SEC * HZ);
+ msleep(POLL_INTERVAL_SEC * 1000);
if (ibmphp_shutdown)
break;
@@ -908,8 +908,7 @@
/* give up the harware semaphore */
up (&semOperations);
/* sleep for a short time just for good measure */
- set_current_state (TASK_INTERRUPTIBLE);
- schedule_timeout (HZ/10);
+ msleep(100);
}
up (&sem_exit);
debug ("%s - Exit\n", __FUNCTION__);
@@ -974,7 +973,7 @@
if (SLOT_PWRGD (pslot->status)) {
// power goes on and off after closing latch
// check again to make sure power is still ON
- long_delay (1 * HZ);
+ msleep(1000);
rc = ibmphp_hpc_readslot (pslot, READ_SLOTSTATUS, &status);
if (SLOT_PWRGD (status))
update = TRUE;
@@ -1147,7 +1146,7 @@
if (CTLR_WORKING (*pstatus) == HPC_CTLR_WORKING_NO)
done = TRUE;
if (!done) {
- long_delay (1 * HZ);
+ msleep(1000);
if (timeout < 1) {
done = TRUE;
err ("HPCreadslot - Error ctlr timeout\n");