From: Alan Cox There is a messy scsi faking vendor driver for this card but this instead is a standard Linux IDE layer driver. Signed-off-by: Andrew Morton --- 25-akpm/drivers/ide/Kconfig | 6 25-akpm/drivers/ide/pci/Makefile | 1 25-akpm/drivers/ide/pci/it8212.c | 664 +++++++++++++++++++++++++++++++++++++++ 25-akpm/include/linux/pci_ids.h | 1 4 files changed, 672 insertions(+) diff -puN drivers/ide/Kconfig~add-support-for-it8212-ide-controllers drivers/ide/Kconfig --- 25/drivers/ide/Kconfig~add-support-for-it8212-ide-controllers 2004-08-15 22:49:15.543240080 -0700 +++ 25-akpm/drivers/ide/Kconfig 2004-08-15 22:49:15.551238864 -0700 @@ -621,6 +621,12 @@ config BLK_DEV_IT8172 ; picture of the board at . +config BLK_DEV_IT8212 + tristate "IT8212 IDE support (Experimental)" + help + This driver adds support for the ITE 8212 IDE RAID controller in + both RAID and pass-through mode. + config BLK_DEV_NS87415 tristate "NS87415 chipset support" help diff -puN /dev/null drivers/ide/pci/it8212.c --- /dev/null 2003-09-15 06:40:47.000000000 -0700 +++ 25-akpm/drivers/ide/pci/it8212.c 2004-08-15 22:49:15.554238408 -0700 @@ -0,0 +1,664 @@ +/* + * linux/drivers/ide/pci/it8212.c Version 0.01 July 2004 + * + * Copyright (C) 2004 Red Hat + * + * May be copied or modified under the terms of the GNU General Public License + * + * Documentation available from + * http://www.ite.com.tw/pc/IT8212F_V04.pdf + * + * The ITE8212 isn't exactly a standard IDE controller. It has two + * modes. In pass through mode then it is an IDE controller. In its smart + * mode its actually quite a capable hardware raid controller disguised + * as an IDE controller. + * + * Errata: + * Rev 0x10 also requires master/slave use the same UDMA timing and + * cannot do ATAPI DMA, while the other revisions can do ATAPI UDMA + * but not MWDMA. + * + * This has a few impacts on the driver + * - In pass through mode we do all the work you would expect + * - In smart mode the clocking set up is done by the controller generally + * - There are a few extra vendor commands that actually talk to the + * controller but only work PIO with no IRQ. + * + * Vendor areas of the identify block in smart mode are used for the + * timing and policy set up. Each HDD in raid mode also has a serial + * block on the disk. The hardware extra commands are get/set chip status, + * rebuild, get rebuild status. + * + * In Linux the driver supports pass through mode as if the device was + * just another IDE controller. If the smart mode is running then + * volumes are managed by the controller firmware and each IDE "disk" + * is a raid volume. Even more cute - the controller can do automated + * hotplug and rebuild. + * + * The pass through controller itself is a little demented. It has a + * flaw that it has a single set of PIO/MWDMA timings per channel so + * non UDMA devices restrict each others performance. It also has a + * single clock source per channel so mixed UDMA100/133 performance + * isn't perfect and we have to pick a clock. Thankfully none of this + * matters in smart mode. ATAPI DMA is not supported. + * + * TODO + * - Rev 0x10 in pass through mode needs UDMA clock whacking + * to work around h/w issues + * - Is rev 0x10 out anywhere - test it if so + * - More testing + * - Find an Innovision 8401D or R board somewhere to test that + * - See if we can kick the cheapo board into smart mode + * ourselves 8) + * - ATAPI UDMA is ok but not MWDMA it seems + * - Better clock strategy + * - RAID configuration ioctls + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +struct it8212_dev +{ + int smart:1, /* Are we in smart raid mode */ + timing10:1; /* Rev 0x10 */ + u8 clock_mode; /* 0, 50 or 66 */ + u8 want[2][2]; /* Mode/Pri log for master slave */ + + /* We need these for switching the clock when DMA goes on/off */ + u8 pio[2]; /* Cached PIO values */ + u8 mwdma[2]; /* Cached MWDMA values */ +}; + +/** + * it8212_clock_strategy + * @hwif: hardware interface + * + * Select between the 50 and 66Mhz base clocks to get the best + * results for this interface. Right now our approach is stupidity + * first until we have the driver stable + */ + +static void it8212_clock_strategy(ide_drive_t *drive) +{ + u8 v; + int sel = 0; + ide_hwif_t *hwif = HWIF(drive); + int clock; + struct it8212_dev *itdev = ide_get_hwifdata(hwif); + /* FIXME: Just to simplify we don't switch clocks once set */ + if(itdev->clock_mode == 0) + { + if(itdev->want[0][0] > itdev->want[1][0]) + clock = itdev->want[0][1]; + else + clock = itdev->want[1][1]; + /* Load this into the controller ? */ + if(clock == 66) + itdev->clock_mode = 66; + else + { + itdev->clock_mode = 50; + sel = 1; + } + pci_read_config_byte(hwif->pci_dev, 0x50, &v); + v &= ~(1 << (1 + hwif->channel)); + v |= sel << (1 + hwif->channel); + pci_write_config_byte(hwif->pci_dev, 0x50, v); + + printk(KERN_INFO "it8212: selected %dMHz clock.\n", itdev->clock_mode); + } +} + +/** + * it8212_ratemask - Compute available modes + * @drive: IDE drive + * + * Compute the available speeds for the devices on the interface. This + * is all modes to ATA133 clipped by drive cable setup. + */ + +static byte it8212_ratemask (ide_drive_t *drive) +{ + u8 mode = 4; + if (!eighty_ninty_three(drive)) + mode = min(mode, (u8)1); + return mode; +} + +/** + * it8212_tuneproc - tune a drive + * @drive: drive to tune + * @mode_wanted: the target operating mode + * + * Load the timing settings for this device mode into the + * controller. By the time we are called the mode has been + * modified as neccessary to handle the absence of seperate + * master/slave timers for MWDMA/PIO. + * + * This code is only used in pass through mode. + */ + +static void it8212_tuneproc (ide_drive_t *drive, byte mode_wanted) +{ + ide_hwif_t *hwif = HWIF(drive); + struct it8212_dev *itdev = ide_get_hwifdata(hwif); + int unit = drive->select.b.unit; + int channel = hwif->channel; + u8 conf; + + /* Spec says 89 ref driver uses 88 */ + static u8 pio_50[] = { 0x88, 0x82, 0x81, 0x32, 0x21 }; + static u8 pio_66[] = { 0xAA, 0xA3, 0xA1, 0x33, 0x31 }; + + static u8 pio_want[] = { 66, 66, 66, 66, 0 }; + + /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */ + itdev->want[unit][0] = pio_want[mode_wanted]; + itdev->want[unit][1] = 1; /* PIO is lowest priority */ + + it8212_clock_strategy(drive); + + /* Program PIO/MWDMA timing bits */ + pci_read_config_byte(hwif->pci_dev, 0x54 + 4 * channel, &conf); + if(itdev->clock_mode == 66) + conf = pio_66[mode_wanted]; + else + conf = pio_50[mode_wanted]; + pci_write_config_byte(hwif->pci_dev, 0x54 + 4 * channel, conf); + itdev->pio[unit] = conf ; +} + +/** + * it8212_tune_mwdma - tune a channel for MWDMA + * @drive: drive to set up + * @mode_wanted: the target operating mode + * + * Load the timing settings for this device mode into the + * controller when doing MWDMA in pass through mode. The caller + * must manage the whole lack of per device MWDMA/PIO timings and + * the shared MWDMA/PIO timing register. + * + * FIXME: before we can enable MWDMA we need to cache PIO/MWDMA + * timings and reload them on ide_dma_on/ide_dma_off_* because they + * occupy the same register. + */ + +static void it8212_tune_mwdma (ide_drive_t *drive, byte mode_wanted) +{ + ide_hwif_t *hwif = HWIF(drive); + struct it8212_dev *itdev = (void *)ide_get_hwifdata(hwif); + int unit = drive->select.b.unit; + int channel = hwif->channel; + u8 conf; + + static u8 dma_50[] = { 0x66, 0x22, 0x21 }; + static u8 dma_66[] = { 0x88, 0x32, 0x31 }; + + static u8 mwdma_want[] = { 0, 66, 0 }; + + itdev->want[unit][0] = mwdma_want[mode_wanted]; + itdev->want[unit][1] = 2; /* MWDMA is low priority */ + + it8212_clock_strategy(drive); + + /* UDMA bits off */ + pci_read_config_byte(hwif->pci_dev, 0x50, &conf); + conf |= 1 << (3 + 2 * channel + unit); + pci_write_config_byte(hwif->pci_dev, 0x50, conf); + + /* Program PIO/MWDMA timing bits */ + pci_read_config_byte(hwif->pci_dev, 0x54 + 4 * channel, &conf); + if(itdev->clock_mode == 66) + conf = dma_66[mode_wanted]; + else + conf = dma_50[mode_wanted]; + pci_write_config_byte(hwif->pci_dev, 0x54 + 4 * channel, conf); + itdev->mwdma[unit] = conf; +} + +/** + * it8212_tune_udma - tune a channel for UDMA + * @drive: drive to set up + * @mode_wanted: the target operating mode + * + * Load the timing settings for this device mode into the + * controller when doing UDMA modes in pass through. + */ + +static void it8212_tune_udma (ide_drive_t *drive, byte mode_wanted) +{ + ide_hwif_t *hwif = HWIF(drive); + struct it8212_dev *itdev = ide_get_hwifdata(hwif); + int unit = drive->select.b.unit; + int channel = hwif->channel; + u8 conf; + + static u8 udma_50[]= { 0x33, 0x31, 0x21, 0x21, 0x11, 0x11, 0x11 }; + static u8 udma_66[]= { 0x44, 0x42, 0x31, 0x21, 0x11, 0x22, 0x11 }; + + static u8 udma_want[] = { 0, 50, 0, 66, 66, 50, 66 }; + + itdev->want[unit][0] = udma_want[mode_wanted]; + itdev->want[unit][1] = 3; /* UDMA is high priority */ + + it8212_clock_strategy(drive); + + /* UDMA on */ + pci_read_config_byte(hwif->pci_dev, 0x50, &conf); + conf &= ~ (1 << (3 + 2 * channel + unit)); + pci_write_config_byte(hwif->pci_dev, 0x50, conf); + + /* Program UDMA timing bits */ + pci_read_config_byte(hwif->pci_dev, 0x56 + 4 * channel + unit, &conf); + if(itdev->clock_mode == 66) + conf = udma_66[mode_wanted]; + else + conf = udma_50[mode_wanted]; + + if(mode_wanted >= 5) + conf |= 0x80; /* UDMA 5/6 select on */ + + pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel + unit, conf); + itdev->mwdma[unit] = 0; +} + +/** + * config_it8212_chipset_for_pio - set drive timings + * @drive: drive to tune + * @speed we want + * + * Compute the best pio mode we can for a given device. We must + * pick a speed that does not cause problems with the other device + * on the cable. + */ + +static void config_it8212_chipset_for_pio (ide_drive_t *drive, byte set_speed) +{ + u8 unit = drive->select.b.unit; + ide_hwif_t *hwif = HWIF(drive); + ide_drive_t *pair = &hwif->drives[1-unit]; + u8 speed = 0, set_pio = ide_get_best_pio_mode(drive, 4, 5, NULL); + u8 pair_pio; + + /* We have to deal with this mess in pairs */ + if(pair != NULL) + { + pair_pio = ide_get_best_pio_mode(pair, 4, 5, NULL); + /* Trim PIO to the slowest of the master/slave */ + if(pair_pio < set_pio) + set_pio = pair_pio; + } + it8212_tuneproc(drive, set_pio); + speed = XFER_PIO_0 + set_pio; + /* XXX - We trim to the lowest of the pair so the other drive + will always be fine at this point until we do hotplug passthru */ + + if (set_speed) + (void) ide_config_drive_speed(drive, speed); +} + +static void config_chipset_for_pio (ide_drive_t *drive, byte set_speed) +{ + config_it8212_chipset_for_pio(drive, set_speed); +} + +/** + * it8212_dma_read - DMA hook + * @drive: drive for DMA + * + * The IT8212 has a single timing register for MWDMA and for PIO + * operations. As we flip back and forth we have to reload the + * clock. + * + * FIXME: for 0x10 model we should reprogram UDMA here + */ + +static int it8212_dma_begin(ide_drive_t *drive) +{ + ide_hwif_t *hwif = HWIF(drive); + struct it8212_dev *itdev = ide_get_hwifdata(hwif); + int unit = drive->select.b.unit; + if(itdev->mwdma[unit]) + pci_write_config_byte(hwif->pci_dev, 0x54 + 4 * hwif->channel, itdev->mwdma[drive->select.b.unit]); + return __ide_dma_begin(drive); +} + +/** + * it8212_dma_write - DMA hook + * @drive: drive for DMA stop + * + * The IT8212 has a single timing register for MWDMA and for PIO + * operations. As we flip back and forth we have to reload the + * clock. + * + * FIXME: for 0x10 model we should reprogram UDMA here + */ + +static int it8212_dma_end(ide_drive_t *drive) +{ + ide_hwif_t *hwif = HWIF(drive); + int unit = drive->select.b.unit; + struct it8212_dev *itdev = ide_get_hwifdata(hwif); + int ret = __ide_dma_end(drive); + + if(itdev->mwdma[unit]) + pci_write_config_byte(hwif->pci_dev, 0x54 + 4 * hwif->channel, itdev->pio[drive->select.b.unit]); + return ret; +} + + +/** + * it8212_tune_chipset - set controller timings + * @drive: Drive to set up + * @xferspeed: speed we want to achieve + * + * Tune the ITE chipset for the desired mode. If we can't achieve + * the desired mode then tune for a lower one, but ultimately + * make the thing work. + */ + +static int it8212_tune_chipset (ide_drive_t *drive, byte xferspeed) +{ + + ide_hwif_t *hwif = HWIF(drive); + struct it8212_dev *itdev = ide_get_hwifdata(hwif); + u8 speed = ide_rate_filter(it8212_ratemask(drive), xferspeed); + + switch(speed) { + case XFER_PIO_4: + case XFER_PIO_3: + case XFER_PIO_2: + case XFER_PIO_1: + case XFER_PIO_0: + if(!itdev->smart) + it8212_tuneproc(drive, (speed - XFER_PIO_0)); + break; + /* MWDMA tuning is really hard because our MWDMA and PIO + timings are kept in the same place. We can switch in the + host dma on/off callbacks */ + case XFER_MW_DMA_2: + case XFER_MW_DMA_1: + case XFER_MW_DMA_0: + if(!itdev->smart) + it8212_tune_mwdma(drive, (speed - XFER_MW_DMA_0)); + break; + case XFER_UDMA_6: + case XFER_UDMA_5: + case XFER_UDMA_4: + case XFER_UDMA_3: + case XFER_UDMA_2: + case XFER_UDMA_1: + case XFER_UDMA_0: + if(!itdev->smart) + it8212_tune_udma(drive, (speed - XFER_UDMA_0)); + break; + default: + return 1; + } + /* + * In smart mode the clocking is done by the host controller + * snooping the mode we picked. The rest of it is not our problem + */ + return (ide_config_drive_speed(drive, speed)); +} + +/** + * config_chipset_for_dma - configure for DMA + * @drive: drive to configure + * + * Called by the IDE layer when it wants the timings set up. + */ + +static int config_chipset_for_dma (ide_drive_t *drive) +{ + u8 speed = ide_dma_speed(drive, it8212_ratemask(drive)); + + config_chipset_for_pio(drive, !speed); + + if (!speed) + return 0; + + if (ide_set_xfer_rate(drive, speed)) + return 0; + + if (!drive->init_speed) + drive->init_speed = speed; + + return ide_dma_enable(drive); +} + +/** + * it8212_configure_drive_for_dma - set up for DMA transfers + * @drive: drive we are going to set up + * + * Set up the drive for DMA, tune the controller and drive as + * required. If the drive isn't suitable for DMA or we hit + * other problems then we will drop down to PIO and set up + * PIO appropriately + */ + +static int it8212_config_drive_for_dma (ide_drive_t *drive) +{ + ide_hwif_t *hwif = HWIF(drive); + struct hd_driveid *id = drive->id; + + if ((id->capability & 1) != 0 && drive->autodma) { + /* Consult the list of known "bad" drives */ + if (__ide_dma_bad_drive(drive)) + goto fast_ata_pio; + + if ((id->field_valid & 4) && it8212_ratemask(drive)) { + if (id->dma_ultra & hwif->ultra_mask) { + /* Force if Capable UltraDMA */ + int dma = config_chipset_for_dma(drive); + if ((id->field_valid & 2) && !dma) + goto try_dma_modes; + } + } else if (id->field_valid & 2) { +try_dma_modes: + if ((id->dma_mword & hwif->mwdma_mask) || + (id->dma_1word & hwif->swdma_mask)) { + /* Force if Capable regular DMA modes */ + if (!config_chipset_for_dma(drive)) + goto no_dma_set; + } + } else if (__ide_dma_good_drive(drive) && + (id->eide_dma_time < 150)) { + /* Consult the list of known "good" drives */ + if (!config_chipset_for_dma(drive)) + goto no_dma_set; + } else { + goto fast_ata_pio; + } + return hwif->ide_dma_on(drive); + } else if ((id->capability & 8) || (id->field_valid & 2)) { +fast_ata_pio: +no_dma_set: + config_chipset_for_pio(drive, 1); + return hwif->ide_dma_off_quietly(drive); + } + /* IORDY not supported */ + return 0; +} + +/** + * init_chipset_it8212 - set up an ITE device + * @dev: PCI device + * @name: device name + * + */ + +static unsigned int __devinit init_chipset_it8212(struct pci_dev *dev, const char *name) +{ + return 0; +} + +/** + * ata66_it8212 - check for 80 pin cable + * @hwif: interface to check + * + * Check for the presence of an ATA66 capable cable on the + * interface. Note that the firmware writes bits 4-7 having done + * the drive side sampling. This may impact hotplug. + */ + +static unsigned int __devinit ata66_it8212(ide_hwif_t *hwif) +{ + u16 iocfg; + + pci_read_config_word(hwif->pci_dev, 0x40, &iocfg); + if(iocfg & (1 << (4 + 2*hwif->channel))) + return 1; + return 0; +} + +/** + * init_hwif_it8212 - set up hwif structs + * @hwif: interface to set up + * + * We do the basic set up of the interface structure. The IT8212 + * requires several custom handlers so we override the default + * ide DMA handlers appropriately + */ + +static void __devinit init_hwif_it8212(ide_hwif_t *hwif) +{ + struct it8212_dev *idev = kmalloc(sizeof(struct it8212_dev), GFP_KERNEL); + u8 conf; + + if(idev == NULL) + { + printk(KERN_ERR "it8212: out of memory, falling back to legacy behaviour.\n"); + goto fallback; + } + memset(idev, 0, sizeof(*idev)); + ide_set_hwifdata(hwif, idev); + + pci_read_config_byte(hwif->pci_dev, 0x50, &conf); + if(conf & 1) + { + if(hwif->channel == 0) + printk(KERN_INFO "it8212: controller in RAID mode.\n"); + idev->smart = 1; + } + else if(hwif->channel == 1) + printk(KERN_INFO "it8212: controller in pass through mode.\n"); + + /* + * Not in the docs but according to the reference driver + * this is neccessary. + */ + pci_read_config_byte(hwif->pci_dev, 0x08, &conf); + if(conf == 0x10) + idev->timing10 = 1; +#if 0 /* Needs more research */ + else + hwif->atapi_dma = 1; +#endif + + if(idev->timing10 && !idev->smart) + { + printk(KERN_WARNING "it8212: DMA is not currently supported on revision 0x10 in pass through.\n"); + goto fallback; + } + + hwif->speedproc = &it8212_tune_chipset; + hwif->tuneproc = &it8212_tuneproc; + + /* MWDMA/PIO clock switching for pass through mode */ + if(!idev->smart) + { + hwif->ide_dma_begin = &it8212_dma_begin; + hwif->ide_dma_end = &it8212_dma_end; + } + + if (!hwif->dma_base) + goto fallback; + + hwif->ultra_mask = 0x7f; + hwif->mwdma_mask = 0x07; + hwif->swdma_mask = 0x07; + + + hwif->ide_dma_check = &it8212_config_drive_for_dma; + if (!(hwif->udma_four)) + hwif->udma_four = ata66_it8212(hwif); + + /* + * The BIOS often doesn't set up DMA on this controller + * so we always do it. + */ + + hwif->autodma = 1; + hwif->drives[0].autodma = hwif->autodma; + hwif->drives[1].autodma = hwif->autodma; + return; + +fallback: + hwif->autodma = 0; + hwif->drives[0].autotune = 1; + hwif->drives[1].autotune = 1; + return; +} + +#define DECLARE_ITE_DEV(name_str) \ + { \ + .name = name_str, \ + .init_chipset = init_chipset_it8212, \ + .init_hwif = init_hwif_it8212, \ + .channels = 2, \ + .autodma = AUTODMA, \ + .bootable = ON_BOARD, \ + } + +static ide_pci_device_t it8212_chipsets[] __devinitdata = { + /* 0 */ DECLARE_ITE_DEV("IT8212"), +}; + +/** + * it8212_init_one - pci layer discovery entry + * @dev: PCI device + * @id: ident table entry + * + * Called by the PCI code when it finds an ITE8212 controller. + * We then use the IDE PCI generic helper to do most of the work. + */ + +static int __devinit it8212_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + ide_setup_pci_device(dev, &it8212_chipsets[id->driver_data]); + return 0; +} + +static struct pci_device_id it8212_pci_tbl[] = { + { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8212, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + { 0, }, +}; + +MODULE_DEVICE_TABLE(pci, it8212_pci_tbl); + +static struct pci_driver driver = { + .name = "ITE8212 IDE", + .id_table = it8212_pci_tbl, + .probe = it8212_init_one, +}; + +static int it8212_ide_init(void) +{ + return ide_pci_register_driver(&driver); +} + +module_init(it8212_ide_init); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("PCI driver module for the ITE 8212"); +MODULE_LICENSE("GPL"); diff -puN drivers/ide/pci/Makefile~add-support-for-it8212-ide-controllers drivers/ide/pci/Makefile --- 25/drivers/ide/pci/Makefile~add-support-for-it8212-ide-controllers 2004-08-15 22:49:15.545239776 -0700 +++ 25-akpm/drivers/ide/pci/Makefile 2004-08-15 22:49:15.554238408 -0700 @@ -13,6 +13,7 @@ obj-$(CONFIG_BLK_DEV_HPT34X) += hpt34x. obj-$(CONFIG_BLK_DEV_HPT366) += hpt366.o #obj-$(CONFIG_BLK_DEV_HPT37X) += hpt37x.o obj-$(CONFIG_BLK_DEV_IT8172) += it8172.o +obj-$(CONFIG_BLK_DEV_IT8212) += it8212.o obj-$(CONFIG_BLK_DEV_NS87415) += ns87415.o obj-$(CONFIG_BLK_DEV_OPTI621) += opti621.o obj-$(CONFIG_BLK_DEV_PDC202XX_OLD) += pdc202xx_old.o diff -puN include/linux/pci_ids.h~add-support-for-it8212-ide-controllers include/linux/pci_ids.h --- 25/include/linux/pci_ids.h~add-support-for-it8212-ide-controllers 2004-08-15 22:49:15.547239472 -0700 +++ 25-akpm/include/linux/pci_ids.h 2004-08-15 22:49:15.557237952 -0700 @@ -1641,6 +1641,7 @@ #define PCI_VENDOR_ID_ITE 0x1283 #define PCI_DEVICE_ID_ITE_IT8172G 0x8172 #define PCI_DEVICE_ID_ITE_IT8172G_AUDIO 0x0801 +#define PCI_DEVICE_ID_ITE_8212 0x8212 #define PCI_DEVICE_ID_ITE_8872 0x8872 #define PCI_DEVICE_ID_ITE_IT8330G_0 0xe886 _